Navigation

Home
DIY Mic Pre Kits
DIY Projects
Home Studio Guide
Electronics Bookstore
Home Studio Equipment List

Search


Categories

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

On this page

Sony MXP-3036 Preamp + EQ
DIY: Racking Sony MXP Preamps and EQ modules - Part 2
DIY: PSU PCB
DIY: Racking Sony MXP Preamps and EQ modules

Archive

October, 2008 (1)
September, 2008 (1)
August, 2008 (5)
July, 2008 (6)
June, 2008 (2)
May, 2008 (1)
April, 2008 (1)
March, 2008 (2)
February, 2008 (2)
January, 2008 (3)
December, 2007 (5)
November, 2007 (7)
April, 2007 (10)
March, 2007 (3)
February, 2007 (3)
January, 2007 (11)
December, 2006 (11)
November, 2006 (11)

Blogroll

RSS 2.0 | Atom 1.0 | CDF

Send mail to the author(s) E-mail

Total Posts: 88
This Year: 0
This Month: 0
This Week: 0
Comments: 9

SC-1 Mic Preamp NOW ON SALE!!!!

After many months of development, testing, troubleshooting, frustration, problems, and accomplishments... the SC-1 mic preamp kit, PSU-1848 power supply kit and power transformer kits are now available for sale!

Click here to ORDER

Photo of a finished SC-1 mic preamp kit!  (Note: XLR jacks and wires shown on picture not included in the kit.)

Features:
- Low-Noise, transformerless, High-Quality Mic Preamp
- All solid-state design, using chipsets from THAT Corp and Burr-Brown
- Soft-start, slow ramp-on +48V phantom power
- Crystal clear Red LED indicator for phantom power
- Electronically balanced input and output stages
- 12-position Grayhill gain selector switch
- Gain range from +6 to +72dB, in 6dB increments
- Input RFI protection
- Input clamping protection
- Output surge protection circuit
- Output RFI protection
... read more...

Download PDF file of Assembly Guide/Kit Instructions

Related products like the PSU-1848 Power Supply Kit, Power Transformer Kit, Power Control Kit are also available for sale. Click here.
 Saturday, February 10, 2007
Sony MXP-3036 Preamp + EQ
Sunday, February 11, 2007 12:46:24 AM (Central Standard Time, UTC-06:00) (  |  |  )
It's done... some pictures.  Using my custom PCB for the power supply, and an MCI output transformer on the outputs to convert it to balanced outs.

It works... sounds nice and clean!  The EQ lets you sculpt the sound nicely. No hum, no noise. It's great!



Read more ...
Comments | Trackback | # 
 Thursday, January 25, 2007
DIY: Racking Sony MXP Preamps and EQ modules - Part 2
Friday, January 26, 2007 3:14:48 AM (Central Standard Time, UTC-06:00) (  |  )
This is a continuation of my Sony Racking Job. Click here for previous article.
http://diy-central.com/DIYRackingSonyMXPPreampsAndEQModules.aspx

Things are progressing nicely. Some photos.

Finally cut the hole for the EQ section... took about 2+ hours... it's a pain doing this. And I have to be careful not to make the square holes too big because the tolerances are very tight.



Some closeup photos of the Preamp and EQ module.



Read more ...
Comments | Trackback | # 
DIY: PSU PCB
Friday, January 26, 2007 2:48:53 AM (Central Standard Time, UTC-06:00) (  |  |  )
This is a continuation from this article.
http://www.diy-central.com/DIYSplitPowerSupplyWith48VPhantomPower.aspx

Well, I received the PCBs today but it seems there was a manufacturing error. Everything is flipped/mirrored... Here's how the top layer looks like... the bottom layer is also flipped/mirrored.

BUMMER!



I sent this picture to the manufacturer along with what the Eagle board is supposed to look like. I emailed them... and within a couple of hours, I got a call from them on the phone apologizing for the mistake and they found out where in their process they had the mistake... they're going to remanufacture my boards and resend them to me at no charge!  Talk about great service!  The quality of the boards and it's workmanship do look very nice too, and their prices are great.

This is my first order from them, and even if they did screwed this up, I think I'll use them in the future. I like how they handled the problem very well and took steps to correct it.

I'll keep you guys updated about the progress.


Comments | Trackback | # 
 Saturday, January 20, 2007
DIY: Racking Sony MXP Preamps and EQ modules
Saturday, January 20, 2007 10:31:43 PM (Central Standard Time, UTC-06:00) (  |  |  )
I decided to rack the few remaining Sony MXP preamp and EQ modules I have. This particular mic pre module is using a discrete opamp enclosed in some green colored epoxy or something.

I've already racked a previous Sony mic pre and EQ, so I want this 2nd unit to match the layout of the first one I did. The only difference is this particular project, the mic pre does not have the Jensen transformers, and instead is using some discrete opamp, and will be in a black 1u case.

Here are some preliminary pictures.



The Mic Pre and EQ module I'll be racking.



Preparing the 1u front panel for drilling holes.

Having a drill press makes the job so much easier than using a hand drill. Safety first... don't forget to use goggles. Freak accidents happen, like a drill bit breaking and flying into your eye! (good thing I had the goggles!) So no matter show "quick" a job it is, don't forget your safety glasses or goggles.



Read more ...
Comments | Trackback | # 
< noscript>